FreeBSD 7.0 manual page repository

FreeBSD is a free computer operating system based on BSD UNIX originally. Many IT companies, like DeployIS is using it to provide an up-to-date, stable operating system.

wb - Winbond W89C840F Fast Ethernet device driver

 

NAME

      wb - Winbond W89C840F Fast Ethernet device driver
 

SYNOPSIS

      To compile this driver into the kernel, place the following lines in your
      kernel configuration file:
 
            device miibus
            device wb
 
      Alternatively, to load the driver as a module at boot time, place the
      following line in loader.conf(5):
 
            if_wb_load="YES"
 

DESCRIPTION

      The wb driver provides support for PCI Ethernet adapters and embedded
      controllers based on the Winbond W89C840F Fast Ethernet controller chip.
      The 840F should not be confused with the 940F, which is an NE2000 clone
      and only supports 10Mbps speeds.
 
      The Winbond controller uses bus master DMA and is designed to be a DEC
      ’tulip’ workalike.  It differs from the standard DEC design in several
      ways: the control and status registers are spaced 4 bytes apart instead
      of 8, and the receive filter is programmed through registers rather than
      by downloading a special setup frame via the transmit DMA engine.  Using
      an external PHY, the Winbond chip supports both 10 and 100Mbps speeds in
      either full or half duplex.
 
      The wb driver supports the following media types:
 
      autoselect            Enable autoselection of the media type and options.
                            This is only supported if the PHY chip attached to
                            the Winbond controller supports NWAY autonegotia‐
                            tion.  The user can manually override the autose‐
                            lected mode by adding media options to the
                            /etc/rc.conf file.
 
      10baseT/UTP           Set 10Mbps operation.  The mediaopt option can also
                            be used to select either full-duplex or half-duplex
                            modes.
 
      100baseTX             Set 100Mbps (Fast Ethernet) operation.  The
                            mediaopt option can also be used to select either
                            full-duplex or half-duplex modes.
 
      The wb driver supports the following media options:
 
      full-duplex           Force full duplex operation
 
      half-duplex           Force half duplex operation.
 
      Note that the 100baseTX media type is only available if supported by the
      adapter.  For more information on configuring this device, see
      ifconfig(8).
 

HARDWARE

      The wb driver supports Winbond W89C840F based Fast Ethernet adapters and
      embedded controllers including:
 
            Trendware TE100-PCIE
 

DIAGNOSTICS

      wb%d: couldn     t map memory  A fatal initialization error has occurred.
 
      wb%d: couldn     t map interrupt  A fatal initialization error has occurred.
 
      wb%d: watchdog timeout  The device has stopped responding to the network,
      or there is a problem with the network connection (cable).
 
      wb%d: no memory for rx list  The driver failed to allocate an mbuf for
      the receiver ring.
 
      wb%d: no memory for tx list  The driver failed to allocate an mbuf for
      the transmitter ring when allocating a pad buffer or collapsing an mbuf
      chain into a cluster.
 
      wb%d: chip is in D3 power state -- setting to D0  This message applies
      only to adapters which support power management.  Some operating systems
      place the controller in low power mode when shutting down, and some PCI
      BIOSes fail to bring the chip out of this state before configuring it.
      The controller loses all of its PCI configuration in the D3 state, so if
      the BIOS does not set it back to full power mode in time, it will not be
      able to configure it correctly.  The driver tries to detect this condi‐
      tion and bring the adapter back to the D0 (full power) state, but this
      may not be enough to return the driver to a fully operational condition.
      If you see this message at boot time and the driver fails to attach the
      device as a network interface, you will have to perform second warm boot
      to have the device properly configured.
 
      Note that this condition only occurs when warm booting from another oper‐
      ating system.  If you power down your system prior to booting FreeBSD,
      the card should be configured correctly.
      arp(4), miibus(4), netintro(4), ng_ether(4), ifconfig(8)
 

HISTORY

      The wb device driver first appeared in FreeBSD 3.0.
 

AUTHORS

      The wb driver was written by Bill Paul 〈wpaul@ctr.columbia.edu〉.
 

BUGS

      The Winbond chip seems to behave strangely in some cases when the link
      partner switches modes.  If for example both sides are set to 10Mbps
      half-duplex, and the other end is changed to 100Mbps full-duplex, the
      Winbond’s receiver suddenly starts writing trash all over the RX descrip‐
      tors.  The wb driver handles this by forcing a reset of both the con‐
      troller chip and attached PHY.  This is drastic, but it appears to be the
      only way to recover properly from this condition.
 

Sections

Based on BSD UNIX
FreeBSD is an advanced operating system for x86 compatible (including Pentium and Athlon), amd64 compatible (including Opteron, Athlon64, and EM64T), UltraSPARC, IA-64, PC-98 and ARM architectures. It is derived from BSD, the version of UNIX developed at the University of California, Berkeley. It is developed and maintained by a large team of individuals. Additional platforms are in various stages of development.